A GR5 (Ti-6Al-4V) forging cannot be bought on price alone: the same flange shape can be cut from bar, closed-die forged or rolled as a ring, and those routes are not interchangeable in pressure or fatigue service. Sourcing Ti-6Al-4V forgings and flanges from China starts with the process route, then the material standard, then the paperwork that proves both.
“Forged” should mean the shape was produced by hot deformation of billet, so grain flow follows the contour instead of being cut across it. GR5 is forged in the alpha-beta region, well below its beta transus of roughly 995 °C typical, then heat treated and machined. If a supplier cannot state the route, the billet source and the reduction applied, treat the offer as a bar-machining price — that is usually what it is.
Each route has a different cost structure and a different set of questions worth asking before the order:
| Route | What it gives you | Typical fit | Question to ask |
|---|---|---|---|
| Closed-die forging | Contoured grain flow, near-net shape | Brackets, valve bodies, hub parts in volume | Who owns the die, and can it transfer? |
| Open-die forging | Sound centre, heavy section | Large blocks and discs, small quantities | What reduction was applied to the billet? |
| Rolled ring | Circumferential grain flow, no weld seam | Large flanges above roughly 300 mm | Rolled from pierced billet, or cut from plate? |
| Bar plus machining | Fastest lead time, no tooling | Prototypes and one-off spares | Is it quoted honestly as bar stock? |
A titanium flange is bought against two documents at once. Dimensions, facing and pressure class normally come from ASME B16.5 up to NPS 24, or ASME B16.47 above that; the material is specified separately, and for forgings that means ASTM B381, in GR5 or GR2 (commercially pure titanium) as the service requires. State the flange type — welding neck for cyclic and high-pressure duty, slip-on where cost dominates, blind for closures, lap joint where bore alignment matters — plus bore, schedule and facing finish (Ra 3.2 to 6.3 µm is typical for a raised face), and whether the blank is a rolled ring or a closed-die forging. Left to discretion, a delivery arrives dimensionally correct and metallurgically wrong.
The certificate package is part of the product: an EN 10204 3.1 mill test report tied to the heat number, chemistry including oxygen and nitrogen, properties from the same heat and condition, and a dimensional report against the drawing. One limit worth knowing: hand-held XRF reads alloying elements and will separate GR5 from GR9 (Ti-3Al-2.5V) or GR2, but it cannot measure oxygen, so it cannot separate Grade 5 (Ti-6Al-4V) from Grade 23 (Ti-6Al-4V ELI) — that difference lives in the mill analysis, which is why part marking and certificate must agree. Add ultrasonic and penetrant records only where the drawing or purchase order calls for them, and specify protective packing: on a machined flange face, a gouge is a leak path, not a cosmetic mark.
As an integrated titanium supplier we supply GR5 and Grade 23 forgings and flanges to the drawing — closed-die and open-die blanks, rolled rings and machined flanges — with forging, heat treatment, machining and inspection handled as one controlled release. Specification and revision, inspection scope and certification are agreed in the RFQ and stated on the purchase order; nothing is assumed on your behalf. MOQs run from a single trial piece to production releases, tooling is settled before the order, lead time is quoted with the offer, and one accountable contact owns the job from drawing review to dispatch. Buyers fixing the input stock first will find the mill forms in our titanium bar and rod range, and the ASTM B348 and AMS 4928 comparison for bar and billet covers the certification that travels with forging stock.
ASTM B381 is the usual specification for titanium alloy forgings, with Grade 5 covering Ti-6Al-4V. AMS 4928 is invoked when an aerospace-grade annealed bar, billet, ring or forging condition is required. The applicable specification and its revision are stated in the purchase order, and inspection is confirmed against the drawing and RFQ.
A forged flange is hot deformed to shape, so grain flow follows the profile and the section is sound through the thickness. A machined flange is cut from bar or plate — acceptable for many duties, but with grain flow running straight through the part and more material wasted. Both can meet the same dimensions, so the route must be specified, not inferred.
It confirms the alloying elements — roughly 6% aluminium and 4% vanadium — and will reject a GR2 or GR9 mix-up. It cannot measure oxygen, so it will not separate Grade 5 from Grade 23 ELI. Use PMI as a screening tool and the mill analysis for the oxygen and nitrogen values that define the grade.
Email the drawing, alloy and condition, quantity, NDT scope and documentation requirements to FDtitanium and we will return an offer stating the material specification, forging route, inspection scope and lead time up front, so suppliers compare like for like.
© 2026. Alle Rechte vorbehalten. Zhangjiagang FD Titanium Industries Co.,LTD